Out of stock
SKU: FRG686008-BL
UPC: 822320013351
MPN: 686008-BL
The Fragola 686008-BL is a 60-degree PTFE hose end fitting built for fuel systems, oil lines, and brake plumbing where chemical resistance and leak-free connections matter. This -8 AN fitting connects directly to Fragola Series 6000 PTFE hose, eliminating the fuel permeation problems that plague standard rubber racing hose. At TSA, we stock Fragola fittings for builders who need reliable fluid transfer components that hold up under pressure. The 60-degree angle provides routing flexibility in tight engine compartments where straight fittings create kink points or interfere with other components.
Fragola machines this fitting from aerospace-quality aluminum to mil-spec tolerances, then finishes it with bright-dip black anodizing for corrosion resistance and a clean appearance. The one-piece construction reduces potential leak paths compared to multi-piece designs. What sets this fitting apart is the double-swivel feature—after installation, you can clock the hose end to fine-tune orientation without breaking the seal or removing the fitting from the port. The -8 AN female thread pattern mates with standard -8 AN male ports found on fuel rails, regulators, filters, and cooler assemblies. Overall dimensions measure 2.00 inches wide by 1.00 inch tall by 4.80 inches deep, compact enough for most plumbing configurations.
This fitting suits drag cars, road race vehicles, off-road trucks, and street-driven performance builds where factory fuel lines have been replaced with AN plumbing. The PTFE liner handles gasoline, E85, methanol, and oil without degradation. Pair it with matching Fragola hose and additional fittings from our parts and accessories selection to complete your fluid system. Made in the United States, the 686008-BL reflects Fragola's four decades of experience supplying professional racing teams and serious enthusiasts with fittings that perform under demanding conditions.
| Specification | Detail |
|---|---|
| Brand | FRAGOLA |
| Model/MPN | 686008-BL |
| SKU | FRG686008-BL |
| UPC | 822320013351 |
| Shipping Weight | 0.12 lbs |
| Dimensions | 2.00 in W x 1.00 in H x 4.80 in D |
| Hose Size | -8 AN |
| Fitting Size | -8 AN Female |
| Angle | 60 degrees |
| Color | Black |
| Finish | Bright-dip anodized black |
| Material | Aerospace-quality aluminum |
| Design | Reusable swivel with double-swivel design |
| Compatibility | Fragola Series 6000 PTFE hose |
| Country of Origin | United States |
This fitting is designed as a direct fit for Fragola Series 6000 PTFE hose in -8 AN size. The reusable design allows assembly without special crimping equipment—you cut the hose to length, slide the socket over the hose, and thread the fitting into place.
Yes. The double-swivel design allows you to clock the hose end orientation after the fitting is installed in the port. This eliminates the need to remove and reinstall fittings when fine-tuning hose routing in tight spaces.
PTFE liners resist gasoline, diesel, E85, methanol, brake fluid, and oil without swelling or degradation. Unlike rubber hose that can permeate fuel vapors over time, PTFE maintains a complete seal and does not absorb the fluids passing through it.
Yes. Fragola designs this as a reusable hose end. If you need to shorten your hose run or replace a damaged section, you can disassemble the fitting and reassemble it on new PTFE hose without purchasing a replacement fitting.
WARNING ⚠️ You must be 18 or older to purchase shotgun or rifle ammunition and 21 or older to purchase handgun ammunition and firearms. Please reference our requirements for ammunition orders to "restricted" states HERE. Always make sure you use the correct ammunition for your firearms. Ammo cannot be shipped to a PO Box. Please reference state & local laws before making a firearm or ammunition purchase.
